Filters

(2014) Question 38: What design modifications, such as pre-reforming and ATR (Autothermal Reforming), do you considered for greater feedstock flexibility, higher efficiency and capacity debottlenecking?

We have used pre-reforming to provide feed flexibility especially for feed stocks that are liquid such as naphtha and when co-processed or as an alternate to feeds such as natural gas/ LPG. Pre-reformers can provide for higher efficiencies depending on the relative value of fuel and steam.
Read more

(2014) Question 39: How can we improve temperature control in steam methane reformer tubes? What monitoring practices do you recommend to avoid overheating the furnace tubes?

Regular visual inspection of the reformer tubes is still an important practical way of monitoring the condition of the steam methane reformer especially during transients when online analytical, or instrumentation may be out of calibration or range for the conditions being seen. Historically, the most severe tube failures in SMR’s have occurred during transients, in particular start-ups.
Read more

(2014) Question 40: What are your best practices when crimping pigtails on a hydrogen plant? Are there any metallurgical limitations?

Most owners take the unit down and pinch off the top and the bottom pigtail with a double crimping device and physically separate the pigtail from the cat tube. Itis recommended that the cat tube also be removed. This prevents a damaged or unused tube from distorting and affecting adjacent tubes or perhaps even falling in the firebox causing other damage.
Read more

(2014) Question 41: Can you comment on the use of liquid and/or vaporized naphtha as feed and/or fuel to a hydrogen generation unit?

Johnson Matthey has vast experience in direct reforming of naphtha feedstocks in SMR’s for hydrogen production. The naphtha needs to be vaporized to be processed in the SMR based hydrogen plant. It takes less heat load to reform a mole of naphtha as compared to natural gas, but more COx will be produced, and the carbon formation potential is higher in naphtha which can have an average carbon content of C6 and a tail to C20.
Read more

(2014) Question 43: How has the increased processing of synthetic and other opportunity crudes in a refinery impacted the buildup of HPNA's (Heavy Poly Nuclear Aromatics) in the hydrocracker and affected conversion? What are your strategies to address this?

PCA (Poly Cyclic Aromatics) formation is not a function of processing synthetic or opportunity crudes. Some opportunity crudes can be much easier to process by a HCU due to much lighter EPs thus providing extended run lengths. Feed type, quality, severity of the operation, unit configuration and catalyst choice in the HCU are determining factors for PCA formation.
Read more

(2014) Question 45: Has bromide been reported in your hydroprocessing unit feeds or discovered as ammonium bromide in the reactor effluent exchangers? If bromide is present, do you use the same wash water practices for ammonium chloride deposition sufficient to avoid exchanger fouling? What are the possible sources of bromides

Bromine is in group 17 of the periodic table commonly known as Halogens. Halogen means “salt former”. It is this salt forming nature of the halogen group that makes them key in natural compounds. Halogen anions of Fluoride, Chloride, Bromide, and Iodide are present in living organisms. Further Bromide is present in all organisms, and organobromine is the most common organohalide.
Read more

(2014) Question 46: Silicon uptake on hydrotreating catalysts is an increasing problem. (1) What operating conditions favor maximum silicon pickup by the catalyst? (2) Are there differences between silicon from coker antifoamsand other sources? (3) Does the presence of other contaminants such as nickel and vanadium affect the silicon pick-up by the catalyst? (4) What best practices are you using to monitoring silicon pick-up by the catalyst?

Silicon in feed streams to Hydroprocessing units can pose a threat to catalyst performance and must be properly managed. Silicon acts as a poison to the catalyst by depositing on the surface of catalyst particles blocking active sites and reducing critical HDS and HDN activity. Silicon can be found in a wide range of feed streams and is a concern for all hydrotreaters processing naphtha, distillates, and vacuum gas oils.
Read more