Q&A

(2012) Question 69: How do you detect that amine salts are forming and causing corrosion, either in the fractionator or other locations ahead of the water dew point? What are chemical and operational strategies for mitigation?

We have the chemical service vendor perform routine calculations for ammonia and/or amine salt points. We typically monitor the water dew point ourselves. The amine salt point is to be differentiated from the ammonia chloride salt point. Depending on the amine, a salt point can be higher, and often is.

(2012) Question 70: What are your experiences with processing oil sludge in the delayed coker?

One of our delayed cokers does process crude rag layer draw, wastewater sludge, and oily water. I think they primarily process the crude rag layer, however. What we do here is introduce the sludge after we have steamed the coke bed and established the quench water flow. We then temporarily remove the quench water to allow the sludge injection, and then we maintain a minimum temperature – I think it is around 600°F – to ensure that no oil accumulates in the cutting water.

(2012) Question 71: Is there any test method for performance evaluation of silicon-based antifoam agent used in coker?

Don mentioned the ASTM test procedure. It may also be beneficial to conduct elemental silicon loading. Silicone is a known molecule: dimethylpolysiloxane. The amount of elemental silicon introduced into the drum over a period of time can be tracked and compared with silicon in the distillate. Generally, the biggest step change to silicon loading is improving the chemical feed system.

(2012) Question 72: What are Best Practices for steam rates in cokers, heater velocity steam, valve purge steam, and drum steam out? Do newer, double-fired heater designs use less steam?

Sim Romero with KBC, who is sitting in the audience, will be conducting Coking 101 and will cover these topics. Since I am repeating Sim’s responses, I will summarize the answers.

(2012) Question 73: What is your experience with coke bed instability?

We have seen coke beds collapse during the beginning stages of the quench water addition. We have had operational problems because we were not able to get the quench water into the coke bed. We even tried alternating back and forth between the stripping steam and the quench water, but we were not able to penetrate the coke bed with the quench water.

(2012) Question 74: We have experienced leak issues around gaskets in cyclical and hot temperature services. What solutions have you developed to eliminate these issues?

At one of our two cokers, we use ring joint flanges from the coker heater outlet to the coke drum inlet and have had no leak issues. At the other coker, we have a short section of piping at the coke drum feed inlet that had raised face (RF) with spiral wound gasket drum (SPWD) that would occasionally leak.

(2012) Question 75: Please describe your best turnaround practice for cleaning and inspecting heat exchanger bundles versus replacement.

KBC is a nonoperating company, so we do not operate any equipment or conduct turnarounds. However, we do know that the bundle must be cleaned for inspection. We are accustomed to seeing hydrolancing or chemical cleaning for less severe services.

(2013) Question 29: What are the industry practices to take samples around high-pressure equipment which contain light hydrocarbon and H2S? How do you ensure the samples are handled safely and representative of sample stream?

Our Corpus Christi and Pine Bend refineries had standardized on Texas Sampling Incorporated samplers. They provide a variety of closed loop captured sample systems. We have a Sampler Selection Procedure Flowchart that helps us walk through ‘yes’ or ‘no’ decisions considering high RVP (Reid vapor pressure) material, high-pressure material, high temperature material, high H2S (hydrogen sulfide) options, and plugging potential.

(2013) Question 30: What are your design practices for reactor skin thermocouple requirements in a hydrotreater and a hydrocracker for startups and safe operation?

Our minimal requirement for a hydrotreater is three skin thermocouples at the top and bottom heads of the reactors and a full skin thermocouple at the bottom shell of the reactor just about at the tangent line. The option now is a full skin thermocouple at the top of the shell and the middle of the shell.

(2013) Question 31: What is the threshold concentration of arsenic and phosphorus requiring a dedicated trap system? How are the arsenic and phosphorus trap systems specified,and what are the controlling mechanisms?

Arsenic is a big concern because it is a permanent poison that causes fairly significant activity. We generally see around a 60° Floss per weight percent pickup; so, you will want to pay attention to it. As a side note, it is also common in most fractions of hydrotreating: so anything from naphtha to heavy gas oil.

Find the answer to your technical question in AFPM's extensive Q&A database.

Q&A