Q&A

(2010) Question 91: Assuming the FCCU already has a third stage separator, what are the various options you consider for further reduction of particulate emissions (PM) and what is the expected level of PM to be achieved?

The first thing to consider is the fourth stage collector. For designs that re-introduce the collected fines downstream of the expander, a fourth stage collector with fines removal and filter on the TSS underflow gas will aid in reducing PM.

(2018) Question 1: What are the benefits of alumina treating in sulfuric acid alkylation and HF alkylation? Has this technology been proven commercially?

In the sulfuric acid alkylation process, droplets of acid are found in the effluent stream from the reactor. These droplets, which are formed primarily from the alkylation chemistry itself and the formation of intermediates, are small and stable and cannot be removed by gravity settling and / or coalescing alone.

(2018) Question 2: What metallurgy works well and does not work well for use in alkylation units? In what applications does the alternate metallurgy perform better/worse?

The standard metallurgy for use throughout HF alkylation units is carbon steel. Showing a high degree of corrosion resistance in both low and very high acid concentrations, carbon steel is also useful for its relatively low cost compared to more exotic materials.

(2018) Question 3: What type of release mitigation safety systems do you use for sulfuric acid and HF alkylation units?

Sulfuric acid alkylation units do not require the robust safety systems as the HF Alky units since sulfuric acid is a liquid at atmospheric conditions. The release mitigation safety systems typically used are curbed and/or diked areas to contain the liquid sulfuric acid in event of a leak.

(2018) Question 9: Are you adding unusual feeds to catalytic condensation or oligomerization units?

Refiners have been pursuing the use of more atypical feeds to their olefin oligomerization units for various reasons. Units have historically operated on FCC LPG cuts, but an interest to process Coker LPGs or even heavier FCC olefins have begun.

(2018) Question 52: What are your best practices for wet flue gas scrubber water supply and system monitoring (sampling frequency, instrumentation verification, etc.)? How do you handle the effluent water and any new emerging trends?

Water supply should be managed depending on the system design. The water source used by Motiva is clarified water. Due to the stainless-steel material and the chloride concentration in both the water and the caustic for neutralization the inlet duct temperature is monitored and controlled to prevent Chloride Stress Corrosion Cracking.

(2010) Question 21: Silica uptake on gas oil and diesel hydrotreating units is an increasing problem. In your experience, what is the source of silica in these feeds? Do you have effective ways to manage this silica?

The main source of silicon in Hydrotreaters is polysiloxane compounds (such as polydimethylsiloxane) used to control foaming in delayed coker units. It has also been reported that indigenous silicon is present in some heavy oils.

(2010) Question 22: In your experience, how are ULSD units maximizing catalyst life/ cycle length? Do you use feedstock or catalyst analysis to locate sources of contaminants, especially arsenic?

Many factors impact the cycle length in a ULSD unit, and in order to ensure the longest possible cycle length in such units it is important to: Have an optimal flow distribution and gas mixing using latest generation reactor internals designed for the actual operating conditions. This is very important in order to ensure maximum catalyst utilization with no channeling in the catalyst bed.

(2010) Question 28: The Clean Air Act required refineries to develop and implement a Leak Detection and Repair (LDAR) program to control fugitive emissions. What is the current status of this implementation and who is responsible for it in a typical refinery management structure: production, maintenance or EHS?

Since the inception of the Clean Air Act of 1955 and multiple amendments through 1990, Leak Detection and Repair or LDAR regulations have been a part of air pollution control. Today’s LDAR programs are governed by Federal and State regulations and agreed orders (consent decrees) that provide the control of fugitive emission leaks from process equipment by requiring equipment inspections and leaking equipment repair.

(2010) Question 29: What technologies do you use for treating or recovering VOCs from small-scale truck loading terminals? Discuss the merits associated with each?

The three main VOC treating systems for small scale truck loading are vapor combustion system, flare gas recovery unit, and an adsorption/absorption vapor recovery system.

Find the answer to your technical question in AFPM's extensive Q&A database.

Q&A