Q&A

(2016) Question 34: The cycle life of a high-pressure ULSD unit operating for maximum aromatic saturation and liquid yield is limited by aromatics equilibrium at elevated temperatures. What strategies or solutions do you employ to extend operation with maximum liquid yield?

This question is more related to EOR conditions when you have employed all of the operational techniques but wish to further optimize the EOR performance without yield decline. If you are already maximizing H2 pp (partial pressure), achieving full catalyst utilization with state-of-the art reactor internals, and adjusting bed profiles at MOR/EOR (middle-of-run/end-of-run) to remain in region of optimum aromatic saturation, the following example illustrates the benefits of optimizing the nickel-molybdenum catalyst for your application.

(2010) Question 89: In shifting from partial burn to full burn in a side by side unit, what has been your observed impact on the NOx emissions? What is necessary to achieve 20 ppm NOx?

Several Grace customers successfully operate with NOx emissions less than 20 ppm in full combustion without the use of NOx removal hardware in the flue gas circuit.

(2010) Question 90: Does any refiner use an on-line particulate emissions (PM) analyzer to measure PM concentration and/or particle size distribution in the flue gas? Are any of these analyzers using continuous emission monitoring systems (CEMS)? How reliable and accurate have these systems been?

Sunoco currently has a particulate matter (PM) analyzer in one location on the stack of a Wet Gas Scrubber. It is there to measure Filterable PM only, not particle size distribution. This was installed as a requirement of a local environmental permit.

(2010) Question 91: Assuming the FCCU already has a third stage separator, what are the various options you consider for further reduction of particulate emissions (PM) and what is the expected level of PM to be achieved?

The first thing to consider is the fourth stage collector. For designs that re-introduce the collected fines downstream of the expander, a fourth stage collector with fines removal and filter on the TSS underflow gas will aid in reducing PM.

(2018) Question 46: What is your strategy to minimize main fractionator bottoms (DCO/ Slurry) versus LCO production apart from feed quality/catalyst selection?

The primary operational handles to minimize bottoms production is optimization of the cat to oil in the R&R. As the C/O is increased more of the heavy oils will be converted. As with all good things in the FCC this can be taken too far. Limits can be reached on the actual operating equipment in this process.

(2018) Question 47: Are there any operational parameters that can be manipulated to improve the operation of the slurry circuit and minimize fouling? Can you outline the slurry exchanger circuit recommended design practices to minimize fouling, plugging and erosion?

Temperature: From experience, the rate of coke build-up increases greatly when the bottoms temperature is > 700F (370°C). It is recommended to maintain the bottoms temperature below 680°F (360°C) to be on the safe side.

(2018) Question 49: As the demand for higher octane gasoline components increases and lobbying for a 95 RON gasoline standard continues, how are you adjusting your operations to meet the market demand? What FCC specific changes do you make to produce higher octane gasoline components?

Refiners are optimizing their gasoline blend components to maximize high octane components. Alkylate and reformate yields are becoming increasingly important, as well as minimizing low octane component yields. The emergence of tight oil feeds has created an increase in low octane natural gasoline and LPG saturate production.

(2018) Question 50: Butylene demand and prices in relation to other refined products reached a record level in 2017. What caused it and what can we do in the FCC to produce more butylenes?

Higher demand for butylene is result of octane shortage in the gasoline market stemming from several main causes.

(2018) Question 52: What are your best practices for wet flue gas scrubber water supply and system monitoring (sampling frequency, instrumentation verification, etc.)? How do you handle the effluent water and any new emerging trends?

Water supply should be managed depending on the system design. The water source used by Motiva is clarified water. Due to the stainless-steel material and the chloride concentration in both the water and the caustic for neutralization the inlet duct temperature is monitored and controlled to prevent Chloride Stress Corrosion Cracking.

(2018) Question 55: With new challenges presented by the Refinery Sector and Maintenance Venting Rules oil circuits are taking longer to prepare for maintenance; what successes and challenges have you had in staging shutdown operations to allow for safe entry to the FCC reactor/regenerator section prior to clearing other sections of the unit?

With new challenges presented by the Refinery Sector and Maintenance Venting Rules oil circuits are taking longer to prepare for maintenance; what successes and challenges have you had in staging shutdown operations to allow for safe entry to the FCC reactor/regenerator section prior to clearing other sections of the unit?

Find the answer to your technical question in AFPM's extensive Q&A database.

Q&A