Q&A

(2008) Question 86: The reformer’s feed properties can be affected when the refinery is maximizing refinery diesel yield. How do these changes to reformer feed affect performance with respect to C5+ yield, hydrogen production, cycle length, and economics?

NEWTON (Roddey Engineering Services, Inc.) As everyone knows, we’re not here to discuss how to make more gasoline; we’re here at the conference to learn how to make more diesel, so I just hope you people in here... But whenever you start to talk about maximizing diesel yield from most refineries, what you’re going to talk about is shifting the heavy end of the reformer feed to the diesel stream and so you lower your endpoint to the reformer.

(2008) Question 87: Iron contamination of CCR, cyclic, and semi-regen reformer catalyst is a common problem. What level of iron concentration typically justifies catalyst replacement due to poor catalyst performance?

METKA (Sunoco, Inc.) Typically, iron levels up to approximately 12,000 ppm can be tolerated before a change-out is required. Iron is a support modifier that can affect both the metal and acid sites. There is more of an impact on the acid sites, and iron can impede chloride pick-up and trap sulfur on the catalyst. Iron typically impacts the first reactor in a fixed-bed unit and is primarily a result of upstream corrosion in the naphtha hydrotreater.

(2008) Question 88: What is your experience with feed-side fouling on combined feed/effluent (CFE) exchangers? What is the foulant? How often do you clean them and what cleaning techniques do you use? On Texas Towers (vertical shell & tube exchangers), how do you extract the bundle from the shell if it gets stuck?

NEWTON (Roddey Engineering Services, Inc. Engineering) I’m just going to deal with Roddey Engineering’s experience. I know some people on the panel have different experiences. But as far as feed effluent exchangers go, and especially Texas Towers, we have seen significant fouling on all that we’ve dealt with. Pretty much every refinery that has one, they do not clean the tower.

(2019) Question 2: We have a Selective Hydrogeneration Units (SHU) unit that removes butadiene from the olefin feed to the alkylation unit. What is the typical concentration of hydrogen and light ends in the olefin product leaving the SHU? How do hydrogen and light ends affect alky operations?

THOMAS PORRITT (Chevron U.S.A)
A selective hydrogenation unit or SHU converts diolefins to olefins in a stream before it feeds an alkylation unit.

Below is a basic flow scheme.

Figure Q2 - 1 Selective Hydrogenation Unit Flow Scheme

The typical composition of non-condensable gases and light

(2019) Question 3: What is your experience with ball valves in feed and make-up gas drier circuits in ISOM Units? What strategies have you adopted for monitoring leaks, regular maintenance and achieving longer run length?

DAVINDER MITTAL (HPCL Mittal Energy)

The gas and liquid dryers perform important task of safeguarding the ISOM catalyst from water vapor and other impurities in the make-up hydrogen and hydrocarbon feed.
The dryer switching valves play an important role of directing the inlet/outlet gas streams

(2019) Question 5: How will Tier 3 rules impact gasoline-producing units at your facility?

ABIGAIL SLATER (HollyFrontier)
The Tier 3 gasoline regulation partially took effect in 2017 and will be fully implemented in 2020. The Tier 3 gasoline regulation has impacted the refining industry in a myriad of ways as refiners reduce sulfur further. These impacts will be similar to most refineries

Question 7: What are your typical precious metal recoveries from reforming catalysts? What factors impact this?

BILL KOSTKA (AXENS NORTH AMERICA)
Reported platinum recoveries from reforming catalyst following commercial utilization have typically ranged between 90 and 100 wt% and have rarely been less than 80 wt%. The magnitude of this range is both frustrating and at least somewhat explainable.

How one

Question 49: In the past year, a sulfuric alkylation unit released a significant amount of sulfur dioxide to atmosphere when light hydrocarbon flowed from the reaction zone through the acid blowdown system and into the spent acid tank. What measures do you recommend for preventing this?

We would recommend ensuring that the acid knockout drum be sized large enough to allow the hydrocarbons to disengage in the drum.

Question 51: Reforming unit stabilizer column top trays and overhead condensers can experience fouling with ammonium chloride salts, which are commonly removed by online water washing of the column overhead. What practices do you employ to reduce the risk of rapid corrosion and the potential failure associated with this fouling and subsequent water washing procedure?

Ammonium chloride salts are a common problem in both naphtha reforming and naphtha hydrotreating units.

Question 61: Have you found that you needed to install a methanator upstream of a chlorided catalyst isomerization unit to remove carbon monoxide (CO) from the feed? What is the source of the CO and how much of a difference has the addition of the methanator made to catalyst life? What is the expected payout for the cost of the methanator?

The problem now comes from the oxygen ingress coming in with makeup hydrogen, with the culprit typically being CO and CO2.

Find the answer to your technical question in AFPM's extensive Q&A database.

Q&A