Q&A

(2018) Question 38: How does coke morphology vary with changes in feed quality? What feed tests do you require to quantify the impact on coke quality?

Predicting coke morphology from feed properties has not been 100% successful as the Coker operating conditions can make a difference if the feed is close to the shot coke vs. sponge coke threshold. The traditional approach uses the asphaltene content of the feed divided by the concarbon value of the feed.

(2018) Question 39: What operating conditions increase the generation of coke fines? What reliability issues do you associate with increased fines production?

Coke fine generation is really a function of the coke cutting process. Feed stock and coke drum operations during the actual drum fill cycle have very little to nothing to do with the generation of coke fines.

(2018) Question 40: What is your experience, design and opportunities for on-line crude blending coupled with near infra-red?

What is your experience, design and opportunities for on-line crude blending coupled with near infra-red?

(2018) Question 46: What is your strategy to minimize main fractionator bottoms (DCO/ Slurry) versus LCO production apart from feed quality/catalyst selection?

The primary operational handles to minimize bottoms production is optimization of the cat to oil in the R&R. As the C/O is increased more of the heavy oils will be converted. As with all good things in the FCC this can be taken too far. Limits can be reached on the actual operating equipment in this process.

(2018) Question 47: Are there any operational parameters that can be manipulated to improve the operation of the slurry circuit and minimize fouling? Can you outline the slurry exchanger circuit recommended design practices to minimize fouling, plugging and erosion?

Temperature: From experience, the rate of coke build-up increases greatly when the bottoms temperature is > 700F (370°C). It is recommended to maintain the bottoms temperature below 680°F (360°C) to be on the safe side.

(2018) Question 49: As the demand for higher octane gasoline components increases and lobbying for a 95 RON gasoline standard continues, how are you adjusting your operations to meet the market demand? What FCC specific changes do you make to produce higher octane gasoline components?

Refiners are optimizing their gasoline blend components to maximize high octane components. Alkylate and reformate yields are becoming increasingly important, as well as minimizing low octane component yields. The emergence of tight oil feeds has created an increase in low octane natural gasoline and LPG saturate production.

(2018) Question 50: Butylene demand and prices in relation to other refined products reached a record level in 2017. What caused it and what can we do in the FCC to produce more butylenes?

Higher demand for butylene is result of octane shortage in the gasoline market stemming from several main causes.

(2018) Question 51: For advanced (closed) riser termination systems, where does coke form inside the reactor vessel? What is the typical amount accumulated during a run?

The quantity of coke is heavily dependent on reactor technology, feed quality, and operating conditions. In earlier termination devices the riser outlet was open to the reactor. The vapors would spend a lot of time in the reactor resulting in coking.

(2018) Question 53: In the Third Stage Separator (TSS), what is the expected life of swirl tubes or cyclones assuming good performing regenerator cyclones? Of these two types, which handle upsets/ variable particulate loadings better?

The performance of swirl tubes is comparable with cyclones in terms of separation efficiency. Swirl tubes have distinct advantages over cyclones in being more compact, much easier to construct and have high mechanical integrity.

(2018) Question 55: With new challenges presented by the Refinery Sector and Maintenance Venting Rules oil circuits are taking longer to prepare for maintenance; what successes and challenges have you had in staging shutdown operations to allow for safe entry to the FCC reactor/regenerator section prior to clearing other sections of the unit?

With new challenges presented by the Refinery Sector and Maintenance Venting Rules oil circuits are taking longer to prepare for maintenance; what successes and challenges have you had in staging shutdown operations to allow for safe entry to the FCC reactor/regenerator section prior to clearing other sections of the unit?

Find the answer to your technical question in AFPM's extensive Q&A database.

Q&A